Installation Guide

Style process standard

CategoryNameIllustrate
Cabinet bodyRoof

P2 15mm Particleboard with double embossed surface;Composite P2 80mm wide 15mm particleboard frame strip

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Baseplate

P2 15mm Particleboard with double embossed surface

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Side plate

P2 15mm Particleboard with double embossed surface

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Set partition

P2 15mm Particleboard with double embossed surface

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Cross bars

P2 15mm Particleboard with double embossed surface

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Vertical bars

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Left and right movable partitionP2 15mm double stick particleboardThe width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch
Intermediate movable partition

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Middle movable baffle bar

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Middle left right baffle bar

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Front and rear skirting boards

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Left and right skirting boards

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Door plank 

P2 15mm double stick particleboard

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Door panel decoration strip 1 (single post)

P2 9mmMDF

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Door panel decoration strip 2 (single post)

P2 9mmMDF

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Door panel decoration strip 3 (single post)

P2 9mmMDF

The width, length, depth and distance of the groove meet the requirements of the drawing:The groove width tolerance≤0.2mm,The groove length tolerance≤0.2mm,The groove depth tolerance≤0.2mm,From the side of tolerance≤0.2mm;Groove edge without edge collapse, non - grooving surface without scratch

Backplane 1 (double paste)P2 9mmMDF
Backplane 2 (double paste)P2 9mmMDF

Sealing sideband0.8 thick 3:1 edge sealing tape;The color of the edge band is the same as that of the plate, without white edge
HardwarefittingTracks

1、One 1526mm guide rail;
2、Four pulleys;
3、Four guide rail fixings;
4、Two limiters
5、Four black 6*35 flat head screws;
6、Eight black 6*10 flat head screws;
7、Four black 3.5*14 self-tapping screws

spacer.gif
Back plate clampPlastic back plate clamp 20spacer.gif
Movable partition holder16 plastic metal movable partition holdersspacer.gif
Perfectly affixed8 eccentric key size anaglyph face perfectly affixedspacer.gif
Pour a preventionOne on each side of each cabinetspacer.gif
Desiccant

Adapting piece57 quick pack three in one adapting pieces (need to be assembled and shipped)
Packaging materialingredientsStiff paper corner guard, foam corner guard (2.5"-3" on each side), pearl cotton     spacer.gif      spacer.gif
Packing requirementCartonOrdinary 1A is packed in one piece yellow cartons of 5 layers,the shipping mark information shall be printed according to the confirmed template,see sample provided by customer.
IngredientsThickened Angle protection, separated between the plates with pearl cotton;The corners of the carton shall be protected with corner guards,the Angle guard height must be the same as that of the component;Door panels and frames are wrapped in bubble wrap,door panel front wrapped in two layers of bubble wrap.
Manner of packingOrdinary 1A packing.Product packaging, foam around, cabinet board and board separated with pearl cotton, to avoid the board scratched each other, the corners of the carton with corner guard, all the gaps in the packaging with foam filling.Top and bottom 1cm 15KGS/m³ foam, 180lb carton.Open packing, the outer packing is yellow paper with 5 layers of corrugated paper, and the inner packing is in accordance with the work standard.
ShipmentIn bulkContainer shipment, container loading mode subcontracting first, single package of products after loading.Long cases, heavy cases at the bottom, on top of the light packing
Requirements for quality

1.Hardware accessories without scratches on the surface, coating firm, no fall off, rust.
2.The surface of the finished product has no repair more than 5mm, no obvious repair marks, no impurities, and the installation number corresponding to the installation manual;  Structural holes and grooves are not allowed to be covered by wood chips, dust and sundries. 
3.Installation instructions, product components, hardware accessories are complete and can be used normally, no wrong package, missing package.
4.The package is 1A package, not accepted to drop the box;  After packaging, shake the carton, the products in the box, hardware accessories package without displacement phenomenon;  The packaging of glass, mirror and other fragile products meets the shockproof requirements. 
5.Carton specifications meet the design requirements, the appearance of smooth, flat, no stains.  The carton marks are correct and clearly printed, and fragile products are clearly marked in the carton.  The certificate shall be filled in standard and neatly written. 
6.Sealing glue is smooth and firm.
7.The finished products should not be piled up above the safety height, and meet the requirements of moisture-proof.

1.The panel components have no hollow, cracking, collision (scratch) injury, edge and corner collapse, blistering, warp > 0.2mm and other phenomena;  Corners shall be removed Angle R1.5mm (no deformation, color leakage,);  No wood chips, dust and sundries in structural holes and grooves; 
2.The structure of the finished product is firm and the landing is smooth.  No glue mark, collapse, collision (scratch) injury, nail, and other phenomena.  3.For products with round or sculpted or wrought iron components, the round and sculpted or wrought iron parts should be symmetrical and consistent in shape. 
4.The built-in hardware should be installed with the flat depth tolerance of the board surface ≤0.5mm;  The sliding rail is installed flat and tightly pushed and pulled smoothly, and the tolerance between the upper and lower front and rear edges is less than or equal to 0.5mm. 
5.The surface of the finished product has no obvious scratch, scratch (bump) injury (allowable range is 2mm). 
6.The overall size of the finished product conforms to the requirements of the drawing (the tolerance is 3mm).
7.The overall structure of the product is firm, the landing is smooth, and the components are not loose when shaking.  The joints are tight without obvious gaps. 
8.Drawers and cabinet doors are pushed and pulled smoothly, with proper tightness and uniform gaps around them, and ≤2mm. 
9.Door of tap face, cupboard should be on same level face, wood grain is symmetrical harmonious, do not have abrading phenomenon. 
10.Mirror face, glass cabinet door cleanness does not have glue mark, glue or joint is tight, firm. 
11.Hardware, colloidal and wooden tenon position is correct, installation level, firm, no hammer mark. 
12.The slide rails slide smoothly.


The allowable dimensional tolerance of the assembled finished product is (unit: mm)

Test itemsInspection contentTolerance range
Boundary dimensionLong、 wide、 high2

The diagonal3
PedestalThe bottom foot is flat and stable≤1
Perpendicularity of adjacent sideFrameThe diagonal length≥1000≤3


The diagonal length<1000≤2
Base scoreBuilt-inDouble-leaved doorSeams above and below the door and frame3



Sew


Seams left and right the door and frame2


The gap between the doors2

Single doorThe gap between the doors3


The gap between the doors2

DrawerA seam between the top of the drawer and the frame3


Left and right seam between top of drawer and frame2


The seam between the top of the two drawers2


Seams left and right the door and frame2


The gap between the doors2

Cover mountedDoorPlane clearance between door and frame≤2


DrawerClearance between top drawer and frame plane≤1
Environmental protection standardThe plate is E0(CARB P2)
RemarksThe finished products must be delivered in accordance with the above technical standards. For special parts and requirements, please follow the drawings and material list. The carton contains the assembly diagram.